| Customization: | Available |
|---|---|
| Certification: | ISO9001, CE |
| Salt Rejection Rate: | 99.8% |
|
Still deciding? Get samples of US$ 400/Piece
Request Sample
|
Suppliers with verified business licenses
Audited Supplier Audited by an independent third-party inspection agency
8 Inch Sea Water Desalination RO Membrane for Reverse Osmosis System for Water Treatment
UltraClean SW series special reverse osmosis membrane element for seawater desalination is a high-end reverse osmosis membrane element. The bottom membrane of the support layer has high compression resistance and thick skin.It is dense and has no defects on the membrane surface; it is resistant to abrasion and chemical degradation; and no post-treatment is required in the manufacturing process of membrane elements. Its wide pH resistance and high cleaning efficiency, can use ordinary acid and alkali for strong and efficient cleaning, because the cleaning is more thorough, the long-term operating pressure of the membrane system is lower, and the service life is higher. It can greatly reduce operating costs and bring long-term optimal economics to seawater desalination systems.
Product Highlights
1.High salt rejection
2.Compression resistance, contamination resistance and high cleaning efficiency
3.Improve the overall economics of the desalination system
SWRO Membrane Product Model
| SWRO Reverse Osmosis Membranes | ||||||
| S/NO. | TYPE | MODEL | Effective membrane area ft(m2) |
Parameters(under standard condition) | ||
| Average water flow | minimum desalting rate | stable desalting rate | ||||
| GPD(m³/d) | (%) | (%) | ||||
| 1 | High desalting rate | UC SW-8040-400HR | 400(37) | 6,000(23) | 99.7 | 99.8 |
| 2 | UC SW-8040-440HR | 440(41) | 6,600(25) | 99.7 | 99.8 | |
| 3 | UC SW-4040-82HR | 82(7.6) | 1,180(4.5) | 99.7 | 99.8 | |
| 4 | High desalination and low energy consumption | UC SW-8040-400HRLE | 400(37) | 7,500(28) | 99.7 | 99.8 |
| 5 | UC SW-8040-440HRLE | 440(41) | 82,00(31) | 99.7 | 99.8 | |
| 6 | UC SW-4040-82HRLE | 82(7.6) | 1,450(5.5) | 99.6 | 99.75 | |
| 7 | High desalination and anti-pollution | UC SW-8040-365HRFR/34 | 365(34) | 6,700(25) | 99.7 | 99.8 |
| 8 | Super high desalting rate | UC SW-8040-400XHR | 400(37) | 6,000(23) | 99.7 | 99.82 |
| 9 | UC SW-8040-440XHR | 440(41) | 6,600(25) | 99.7 | 99.82 | |
| 10 | UC SW-4040-82XHR | 82(7.6) | 1,180(4.5) | 99.7 | 99.82 | |
| Test conditions: 32000ppm sodium chloride solution, test pressure 5.5Mpa, temperature 25ºC, PH7-8, recovery of 8%. | ||||||
Membrane Specification
| inch(mm) | B inch(mm) | C inch(mm) |
| 40 (1016) | 1.125 (29) | 7.9 (201) |
| Effective Membrane Area ft²(m²) |
Stablized Rejection Rate(%) |
Minimum Rejection rate(%) |
Flux gpd(m³/d) |
| 440 (41) | 99.82 | 99.7 | 6600 (25) |
Test conditions: inlet pressure 5.5 MPa (800 psi); inlet temperature 25°C (77°F); inlet water quality 2000ppm NaCl; inlet pH 8; recovery 15%.
Operating and Cleaning Limits
| Maximum operating temperature | 113 ºF (45ºC) |
| Maximum operating pressure | 1200 psi (83 bar) |
| Maximum pressure drop | 15 psi (1.0 bar) |
| pH range | 1-13 |
| Maximum Influent Sludge Density Index SDI | 5 |
| Free chlorine tolerance | < 0.1 ppm |
Permeate flow for individual elements may vary ±15 percent from the value specifed.
Active membrane area guaranteed ±4%.
Stabilized salt rejection is generally achieved within 24-48 hours of continuous use; depending upon feedwater characteristics and operating conditions.
Reverse osmosis(RO) system
Reverse osmosis process is the world's advanced, energy-saving and effective separation technology now, with a filtration accuracy of 0.001 μm, to completely separate and remove all particles of soluble salts, colloids, organics, microorganisms, viruses,bacteria, rust, and heavy metals in water. It requires pressure to force pure water across a membrane, leaving the impurities behind.
However, note that reverse osmosis systems are not ideal for treating water that is very hard and/or with significant quantities of contaminants. In this case, to extend the operating life of the membrane, the water should be pre-treated before entering reverse osmosis membranes (filtering, deferrization, etc.).
){kind=link}